;========================================================== ; GSD-File for SPC3 MD38PFSS ; Auto_Baud_supp, 12MBaud ; ; Stand : 2013/07/29 ; File : MD38DP2.GSD ; 汇川变频器 ;=========================================================== #Profibus_DP ; Unit-Definition-List: GSD_Revision=3 Vendor_Name = "INOVANCE" Model_Name = "MD38DP2" Revision = "RV2.0" Ident_Number = 0x0806 Protocol_Ident = 0 Station_Type = 0 Hardware_Release = "MD38PFS_HV1.0" Software_Release = "MD38PFS_SV2.0" ;Supported baudrates 9.6_supp = 1 19.2_supp = 1 45.45_supp = 1 93.75_supp = 1 187.5_supp = 1 500_supp = 1 1.5M_supp = 1 3M_supp = 1 6M_supp = 1 12M_supp = 1 ; Maximum responder time for supported baudrates MaxTsdr_9.6 = 60 MaxTsdr_19.2 = 60 MaxTsdr_45.45 = 60 MaxTsdr_93.75 = 60 MaxTsdr_187.5 = 60 MaxTsdr_500 = 100 MaxTsdr_1.5M = 150 MaxTsdr_3M = 250 MaxTsdr_6M = 450 MaxTsdr_12M = 800 ;Supported hardware features Redundancy = 0 Repeater_Ctrl_Sig = 0 24V_Pins = 0 ; Slave-Specification: Implementation_Type="VPC3" Bitmap_Device = "HI" ; Supported DP features Freeze_Mode_Supp=0 Sync_Mode_Supp=0 Auto_Baud_Supp = 1 Set_Slave_Add_Supp = 0 ; Maximum length of user parameter ;User_Prm_Data_Len=3 Max_User_Prm_Data_Len=55 ; DPV1 related keywords DPV1_Slave = 1 Check_Cfg_Mode = 0 Diag_Update_Delay=7 C1_Read_Write_supp=1 C1_Max_Data_Len=2 C1_Response_Timeout=2000 Diagnostic_Alarm_supp=0 Process_Alarm_supp=0 Pull_Plug_Alarm_supp=0;插入拔出告警 Extra_Alarm_SAP_supp=0 Alarm_Type_Mode_supp=0 WD_Base_1ms_supp=0 Publisher_supp=0 ; Maximum polling frequency Min_Slave_Intervall = 13 Modular_Station = 1 Max_Module=1 Max_Input_Len = 32 Max_Output_Len = 32 Max_Data_Len = 64 Modul_Offset=1 ; Module-Definitions: Fail_Safe = 0 Max_Diag_Data_Len=9 Unit_Diag_Area=24-39 Value(0) = "变频器运行正常" Value(1) = "逆变单元保护" Value(2) = "加速过电流" Value(3) = " 减速过电流" Value(4) = " 恒速过电流" Value(5) = " 加速过电压" Value(6) = " 减速过电压" Value(7) = " 恒速过电压" Value(8) = " 控制电源故障" Value(9) = " 欠压故障" Value(10) = " 变频器过载" Value(11) = " 电机过载" Value(12) = " 输入缺相" Value(13) = " 输出缺相" Value(14) = " 模块过热" Value(15) = " 外部设备故障" Value(16) = " 通讯故障" Value(17) = " 接触器故障" Value(18) = " 电流检测故障" Value(19) = " 电机调谐故障" Value(20) = " 码盘故障" Value(21) = " EEPROM读写故障" Value(22) = " 变频器硬件故障" Value(23) = " 对地短路故障" Value(26) = " 累计运行时间到达故障" Value(27) = " 用户自定义故障1" Value(28) = " 用户自定义故障2" Value(29) = " 累计上电时间到达故障" Value(30) = " 掉载故障" Value(31) = " 运行时PID反馈丢失故障" Value(40) = " 逐波限流故障" Value(41) = " 运行时切换电机故障" Value(42) = " 速度偏差过大故障" Value(43) = " 电机过速度故障" Value(45) = " 电机过温故障" Value(51) = " 初始位置错误" Value(52) = " 变频器通信中断" Unit_Diag_Area_End Slave_Family=0@TdF@INOVANCE/PROFIBUS@DP ; Definition of all available physical modules ; Module 'PPO-01' Module = "PPO-01" 0xF3, 0xF1 1 EndModule Module = "PPO-02" 0xF3, 0xF5 2 EndModule ;Module 'PPO-03' Module = "PPO-03" 0x00,0xF1 3 EndModule ;Module 'PPO-04' Module = "PPO-04" 0x00,0xF5 4 EndModule ;Module 'PPO-05' Module = "PPO-05" 0xF3, 0xFB 5 EndModule ExtUserPrmData = 1 "PZD3(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 2 "PZD4(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 3 "PZD5(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 4 "PZD6(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 5 "PZD7(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 6 "PZD8(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 7 "PZD9(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 8 "PZD10(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 9 "PZD11(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 10 "PZD12(master->slave)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 11 "PZD3(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 12 "PZD4(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 13 "PZD5(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 14 "PZD6(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 15 "PZD7(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 16 "PZD8(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 17 "PZD9(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 18 "PZD10(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 19 "PZD11(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 20 "PZD12(slave->master)" Unsigned16 0xF000 0-65535 EndExtUserPrmData ;自定义Index ExtUserPrmData = 21 "Function code of Index0" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 22 "Function code of Index1" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 23 "Function code of Index2" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 24 "Function code of Index3" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 25 "Function code of Index4" Unsigned16 0xF000 0-65535 EndExtUserPrmData ExtUserPrmData = 26 "Function code of Index5" Unsigned16 0xF000 0-65535 EndExtUserPrmData Ext_User_Prm_Data_Ref(3)=1 Ext_User_Prm_Data_Ref(5)=2 Ext_User_Prm_Data_Ref(7)=3 Ext_User_Prm_Data_Ref(9)=4 Ext_User_Prm_Data_Ref(11)=5 Ext_User_Prm_Data_Ref(13)=6 Ext_User_Prm_Data_Ref(15)=7 Ext_User_Prm_Data_Ref(17)=8 Ext_User_Prm_Data_Ref(19)=9 Ext_User_Prm_Data_Ref(21)=10 Ext_User_Prm_Data_Ref(23)=11 Ext_User_Prm_Data_Ref(25)=12 Ext_User_Prm_Data_Ref(27)=13 Ext_User_Prm_Data_Ref(29)=14 Ext_User_Prm_Data_Ref(31)=15 Ext_User_Prm_Data_Ref(33)=16 Ext_User_Prm_Data_Ref(35)=17 Ext_User_Prm_Data_Ref(37)=18 Ext_User_Prm_Data_Ref(39)=19 Ext_User_Prm_Data_Ref(41)=20 Ext_User_Prm_Data_Ref(43)=21 Ext_User_Prm_Data_Ref(45)=22 Ext_User_Prm_Data_Ref(47)=23 Ext_User_Prm_Data_Ref(49)=24 Ext_User_Prm_Data_Ref(51)=25 Ext_User_Prm_Data_Ref(53)=26